Top Fencing Companies in Stephenson, WI, 54104 | Compare & Call

There are 41 fencing companies server in Stephenson WI

Macs Custom Fence

Macs Custom Fence

Berlin WI 54923
Fences & Gates

Macs Custom Fence, based in Berlin, WI, delivers custom fencing solutions for residential and commercial properties. Our team provides full-service work: new fence and gate installation, repair, paint...

« Previous PagePage 5 of 5Next »


Estimated Fencing Costs in Stephenson, WI

Emergency Fence/Gate RepairStorm / Security Response
$384 - $519
Wood Privacy Fence (Per LF)Estimated Range
$34 - $54
Vinyl / PVC Fencing (Per LF)Estimated Range
$49 - $74
Chain Link Installation (Per LF)Estimated Range
$24 - $34
Aluminum / Ornamental (Per LF)Estimated Range
$59 - $84
Standard Driveway Gate InstallEstimated Range
$1,384 - $1,854

Methodology: Estimates are dynamically generated using localized construction labor multipliers derived from 2025 BLS OEWS (SOC 47-4031) data for Stephenson. Prices reflect standard commercial/residential material specs and labor options adjusted for 2026 economic projections.

Question Answers

How soon can a consultation be scheduled in Central Stephenson?

A site consultation is typically scheduled within 3-5 business days. The standard route from the Stephenson Town Hall via US-41 to Central Stephenson results in a 35-45 minute travel time for the initial assessment. This allows for a review of property lines, zoning, and soil conditions to develop a scope and estimate based on the $45/hr average labor rate.

Am I legally required to notify my neighbor before building a fence in Stephenson?

Yes. Wisconsin Statutes 90.03, the 'Good Neighbor' law, requires written notification for any fence located on a shared property line. For Stephenson in 2026, providing this notice 30 days prior to construction is a legal prerequisite. This applies even with the 0-foot setback, as it is considered a partition fence.

Can I install a smart gate on my pool fence in Wisconsin?

Yes, but the primary mechanism must comply with IBC/IRC Appendix AG pool safety code. Any smart-gate IoT integration must not interfere with the required self-closing and self-latching hardware. In Stephenson, where smart-gate adoption is low, using a certified, integrated latch system is critical to meet modern liability standards and prevent code violations.

How deep should my fence posts be set in Stephenson, WI?

Posts must be set a minimum of 48 inches deep to extend below the frost line. This prevents frost heave, which is the primary cause of post failure and fence racking in Central Stephenson. The 2021 IRC and local amendments require this depth for structural stability against the 115 MPH V-ult wind load. Shallow footings will lift and fail.

Is my fence designed to handle Stephenson's high winds?

A properly engineered fence for the 115 MPH V-ult wind rating uses ASCE 7-22 standards. This dictates closer post spacing (often 6-8 feet on-center), deeper concrete footings, and wind-rated brackets. Standard designs often fail during peak storm season gusts off US-41. The structural system must transfer lateral loads to the ground.

What are the fence height and placement rules for my Stephenson property?

Zoning limits are 4 feet in front yards and 6 feet in rear/side yards. A 0-foot setback is allowed, placing the fence directly on your property line. For corner lots, especially near US-41, you must maintain a clear 'sight triangle'—typically a 10-foot area from the property corner—free of visual obstructions over 3 feet high for traffic safety.

What are the critical steps before digging fence post holes?

First, contact Diggers Hotline of Wisconsin (811) at least three business days before excavation. Hitting a utility line in Central Stephenson is a major liability involving repair costs and fines. Concurrently, file for a permit with the Stephenson permit office; they will verify zoning compliance and often require the utility locate ticket as part of the application.

What fence materials work best with Stephenson's soil and pest conditions?

With low-to-moderate soil corrosivity and a slight/moderate termite risk, pressure-treated pine, cedar, and vinyl are suitable. Use hot-dip galvanized or stainless-steel fasteners to prevent rust streaks from corroding nails. Avoid untreated wood in direct ground contact and ensure all metal posts have a protective coating compatible with the soil pH.



Scroll to Top
CALL US NOW