Top Fencing Companies in Gardena, CA, 90247 | Compare & Call
There are 238 fencing companies server in Gardena CA
High 5 Fencing is a licensed, bonded, and insured fence contractor serving Lake Los Angeles and surrounding areas. We eliminate the middleman to offer contractor-direct pricing without sacrificing qua...
Metal garage doors gates & fences
Since 2010, MHD Corporation has been a licensed contractor (license #991929) serving Tarzana and the greater Los Angeles area. We specialize in custom metal fabrication, concrete work, and the install...
Jc Roll-Up Doors & Folding Gates has been serving Los Angeles since 2008, after the owner spent years installing metal fences, gates, and roll-up doors for a local company starting in 2002. Based in t...
Avi, owner of DNA Gates & Fences in North Hollywood, CA, started the company in 2024 to offer homeowners a higher-quality alternative to standard bolt-together gate kits. Specializing in fully welded ...
Iron Men Gates & Doors Design
Iron Men Gates & Doors Design is a family-owned business serving the Greater Los Angeles area with over 15 years of experience. We specialize in custom ironwork, including the installation and repair ...
A-List Garage Door & Gate is a family-owned business serving Van Nuys and the surrounding San Fernando Valley for over two decades. Founded by Eli, our team specializes in the repair, installation, an...
Signature Iron Works is a veteran-owned metal fabrication company based in Sun Valley, CA, founded by Patrick, an Army veteran who served in Afghanistan. With over 50 years of combined experience, we ...
EZ Gates Service, a licensed gate service company, has been serving Santa Clarita, the San Fernando Valley, and nearby areas since 2005. Under my management since 2005, we carry on my father’s legacy ...
Land Eco Development serves Los Angeles, CA as a full-service general contractor, landscaper, and fencing expert. They handle everything from bathroom remodeling and deck construction to complete land...
FORGEWAYS, a Los Angeles metal fabrication company with roots dating back to Robertos Wrought Iron, rebranded to continue a family tradition of craftsmanship. Founded in 2018, we specialize in custom ...
Estimated Fencing Costs in Gardena, CA
Q&A
What are the height and setback rules for a fence in Gardena?
Gardena zoning enforces a 3.5-foot height limit for front yards and 6 feet for rear yards. The standard setback is 0 feet, allowing construction on the property line. However, corner lots must maintain a clear 'sight triangle' for visibility, a critical rule near high-traffic corridors like I-110.
What fencing material holds up best in Gardena's soil?
Material selection must defeat two factors: moderate soil corrosivity and a moderate-to-heavy termite risk. Pressure-treated lumber, composite, or aluminum are compatible. Use hot-dip galvanized or stainless-steel fasteners to prevent rust streaks from the corrosive soil index.
How soon can a crew start a project in North Gardena?
A consultation typically schedules within 48 hours. The standard route from Rowley Memorial Park uses the I-110 corridor, resulting in a 25-35 minute response window. Mobilization for work follows after DigAlert clearance and permit issuance, with labor factored at a $45/hour average rate.
How deep must fence posts be set in Gardena?
Posts require a minimum 12-inch concrete footing below the local frost line. The IRC mandates this to prevent frost heave, which lifts and racks posts in North Gardena’s moderate-clay soil. A 110 MPH V-ult wind rating further requires deeper embedment for overturning resistance.
Am I legally required to notify my neighbor before building a fence?
Yes. California Civil Code Section 841 defines a 'good neighbor' law for shared boundaries. In 2026, this requires written notice to adjoining owners in Gardena at least 30 days before replacing any partition fence. This formalizes cost-sharing discussions and prevents disputes.
Is a standard fence strong enough for Gardena's wind?
No. A 110 MPH V-ult wind load rating dictates structural design. This engineering standard requires closer post spacing (often 6 feet on-center), continuous concrete footings, and wind-rated structural brackets. These measures resist peak storm season gusts, especially in exposed areas near I-110.
What is required before digging fence post holes?
State law requires a utility locate request via DigAlert (811) at least two working days before excavation. Hitting a gas or fiber line in North Gardena incurs major repair costs and liability. The contractor typically manages this ticket and any associated Gardena permit office paperwork.
Can I install an automated smart gate with a pool?
Yes, but the gate hardware must integrate with pool safety codes. An IoT-operated latch must also meet ASTM F1908-16 and IBC Section 3109 for self-closing, self-latching mechanisms. This dual-compliance is now standard for liability protection in California, merging the high smart-gate trend with mandated safety.
